DIN EN 12764-2005 卫生器具.旋涡浴池的规范

作者:标准资料网 时间:2024-05-03 15:47:52   浏览:9430   来源:标准资料网
下载地址: 点击此处下载
【英文标准名称】:Sanitaryappliances-Specificationforwhirlpoolbaths;GermanversionEN12764:2004
【原文标准名称】:卫生器具.旋涡浴池的规范
【标准号】:DINEN12764-2005
【标准状态】:作废
【国别】:德国
【发布日期】:2005-03
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:安全工程;规范(验收);测定;耐力;设备;电气安全;定义;旋涡式浴缸;试验;安全;安全要求;浴室;加标签;CE标志;文献工作;作标记;划痕;旋涡式浴池设备;卫生器具;旋涡池;浴池设备;质量评定;耐擦伤性;材料强度
【英文主题词】:Bathequipment;Bathrooms;Baths;CEmarking;Conformityassessment;Definition;Definitions;Determination;Electricalsafety;Equipment;Labelling;Marking;Operationalinstructions;Resistance;Safety;Safetyengineering;Safetyrequirements;Sanitaryappliances;Scratchresistance;Scratches;Specification(approval);Strengthofmaterials;Testing;Whirlbathtubs;Whirlingbathappliances;Whirlpool
【摘要】:Thisstandardspecifiesrequirementsforwhirlpoolbaths,havingaratedvoltageofnotmorethan250Vforsinglephaseappliancesand480Vforotherappliances,whichareintendedtobeinstalledinindoordomesticsituationsandusedinaccordancewiththemanufacturer'sinstructionsforpersonalhygiene.Suchwhirlpoolbathsaretestedandsuppliedasacompleteindependentunitdesignedtobedraineddownaftereveryuse.Theycanbetransportedinseveralseparateparts,forassemblyonsite,tofacilitatedelivery.
【中国标准分类号】:Q81
【国际标准分类号】:91_140_70
【页数】:19P.;A4
【正文语种】:德语


下载地址: 点击此处下载
【英文标准名称】:Plastics.Vocabulary
【原文标准名称】:塑料.词汇
【标准号】:BSISO472-1995
【标准状态】:作废
【国别】:
【发布日期】:
【实施或试行日期】:
【发布单位】:英国标准学会(GB-BSI)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:
【国际标准分类号】:
【页数】:
【正文语种】:


Product Code:SAE J737
Title:Hole Spacing for Scraper and Dozer Cutting Edges (Cancelled Aug 2007, Superseded by ISO 7129)
Issuing Committee:Mtc1, Loaders, Crawlers, Scrapers And Mounted Attachments
Scope:This standard is intended for cutting edge sections used on:a. Tractor-scrapers as described in SAE J1057 and J728b. Dozers as described in SAE J729. These cutting edges are further defined in SAE J738 for cross section and SAE J740 and J1580 for hole conformation. (Note: Some inch dimentions in this standard are not equivalent to the corresponding millimeter figures because values which are widely used have been adapted.This standard specifies hole placement along with length and width of the cutting edge.